Custom Sheet Metal Bending Services

Sheet metal bending on 30–400T presses for parts from 0.5 mm to 10 mm — V bends, U channels, Z offsets, hemmed edges and multi-bend formed components, in Q235, SPCC, 304 stainless, copper and aluminium, to customer drawings.

Bending is where most sheet metal parts succeed or fail. Blanking is a cutting calculation; bending is an elastic one. The material springs back, the neutral axis moves, and the flat pattern you calculated in CAD is a prediction rather than a fact.

What we bend

Where volume justifies it, bends run in a stamping die rather than on a press brake — the angle repeats without an operator setting it each cycle. For prototypes and low volume, press-brake bending is usually the cheaper route, and we will say which fits your quantity.

Springback: the part that catches everyone

Every bent part relaxes when the punch withdraws. How much depends on material, thickness, bend radius and the ratio between them. Three practical consequences:

  1. The die is cut to overbend. A 90° target is formed past 90° so that it relaxes to 90°. The amount is established on the sample, not assumed from a table.
  2. Tight radius means more springback, not less. A tight bend concentrates strain, and high-strength or work-hardened material springs back further. This is why 304 stainless behaves differently on the second bend of a U channel than on the first.
  3. Bend angle tolerance is a real specification. If the drawing calls ±1° on a 3 mm Q235 part, that is achievable and worth stating. If it calls ±0.5° on 6 mm stainless, the answer may be a different design rather than a tighter process.

Die clearance and bend radius

Clearance between punch and die is set by material and thickness. Too tight and the material is thinned or scored at the bend; too loose and the radius wanders and the angle becomes unpredictable.

Material Behaviour when bent Practical note
Q235 carbon steel Predictable, forgiving Minimum radius roughly 1× thickness for general work
SPCC cold-rolled Consistent angle, clean surface Tight thickness control gives repeatable results; good for visible parts
304 stainless Work hardens, strong springback Larger radius and different clearance than carbon steel at the same thickness
Aluminium Low strength, tears at tight radius Minimum radius is larger relative to thickness; annealed temper forms better
Copper, brass Forms easily, galling risk Tool surface condition matters; deburring after forming is common

Material detail: materials and surface finishing.

Bend sequence and part design

Order matters on any part with more than one bend. A sequence that looks fine on paper can make the part impossible to hold in the die for the last operation.

More design detail: sheet metal stamping design guidelines and metal stamping capabilities.

Bending versus stamping: which process

Both produce the same geometry; they differ in economics and consistency.

Press-brake bending Stamping die
Tooling cost Low — existing tooling, simple fixtures Higher — a die is built for the part
Per-piece price Higher — one part per cycle, operator involvement Lower at volume
Angle consistency Depends on setup and operator Repeats from the die
Best fit Prototypes, low volume, large parts Repeat production, small to medium parts
Change cost Low Requires die modification

If you are not sure which applies, send the annual quantity with the drawing. That single number usually settles it.

Specification summary

Materials Q235, SPCC, 304 stainless, copper, aluminium, customer-specified grades
Thickness 0.5–10 mm, confirmed per drawing
Press range 30–400 T
Bend types V, U, Z, hem, radiused and multi-bend forms
Finishing Zinc plating, powder coating, electrophoresis, deburring
Sampling 7 days after requirements are confirmed
Production 15–25 days after sample approval
Inspection Height gauges, angle and fixture checks, CMM

Frequently asked questions

Can you bend a part I designed for press-brake production?

Usually yes, but the flat pattern may need adjusting. Press-brake parts often assume sharp internal corners and holes close to the bend line, both of which need changing for a die. We will mark those on your drawing during review.

What bend angle tolerance can you hold?

It depends on material, thickness, radius and springback. We confirm the achievable figure per drawing and state it on the quotation rather than publishing one number that would be wrong for most parts.

Can you form a hemmed edge?

Yes, within the thickness range. A hem needs a flat pattern allowance and a relief at the ends, so it should be on the drawing rather than added after tooling.

My part cracked at the bend — is that the material?

Sometimes, more often it is bend radius relative to thickness, or the bend line running across the grain. Send the failed part and the drawing; the cause is normally visible on the fracture face.

Do you supply the flat pattern?

For tooling we develop it ourselves and confirm it against the sample. If you need a flat pattern for your own records, ask and we will provide it after the first article is approved.

Request a quote

Send the drawing or 3D model, material, thickness, finish, quantity and target date to robert@hmstamping.com, or use the quote request form. Include the annual volume — it decides whether we recommend a die or a press-brake route.

Related: metal stamping · deep drawing · steel brackets · U brackets

◌

LET’S TALK ABOUT YOUR PART

Request a quote

Share your drawing, material and quantity.

Request for quotation

    By submitting this form you agree to be contacted about your enquiry.

    Custom stamping parts made to drawingRequest a quoteWhatsApp
    Export support for customers in Malaysia, Vietnam and Thailand · See what to send for a quote