Custom Deep Drawing Services
Deep drawn sheet metal components — cups, covers, housings, caps and shallow enclosures — produced from customer drawings in SPCC, 304 stainless, aluminium and copper, on 30–400T presses with controlled blank-holding force.
Deep drawing is the process where the metal flows rather than folds. That distinction matters: a drawn part has a wall thickness that changed during forming, and a drawing that ignores it will fail at the third stage rather than the first.
What we deep draw
- Cups, caps and round or rectangular covers
- Enclosures, housings and shielding cans
- Bearing housings and bushings (shallow draws)
- Recessed mounting plates and stiffening forms
- Multi-stage drawn components with pierced features
- Drawn and flanged parts in one tool
Draw ratio: how many stages a part needs
The draw ratio is the blank diameter divided by the punch diameter. Each material tolerates a maximum ratio per stage; exceed it and the wall tears near the punch radius.
As a working guide, the first draw in mild steel typically removes up to about half the blank diameter, and each subsequent stage removes less. Stainless tolerates less per stage because it work hardens, so a cup that draws in two stages in SPCC may need three or four in 304.
What this means practically: a deeper part is not harder because it is deep, it is harder because it needs more stages. Each stage is a die station, a handling step and a chance for wall thinning. We confirm the stage count and the achievable depth during drawing review, before tooling.
Thickness range and an honest limit
Our presses handle 0.5–10 mm material, but deep drawing and heavy plate are not the same job. Our deep drawing work sits mostly in the 0.5–4 mm band. Above that, drawing force and blank-holding requirements climb steeply, and for many geometries a welded or bent-and-formed assembly is the more sensible route than a very large draw.
If your part is thick and deep, we will say so at enquiry and suggest an alternative process rather than quote a draw we cannot hold.
Materials for drawing
| Material | Drawing behaviour | Practical note |
|---|---|---|
| SPCC cold-rolled steel | Good — the standard choice | Consistent thickness gives predictable wall thinning |
| Q235 carbon steel | Good at moderate depth | Softer, less springback than stainless; watch surface finish |
| 304 stainless | Work hardens quickly | Needs more stages and inter-stage annealing at higher reductions |
| Aluminium | Forms easily, tears if pushed | Annealed temper draws far better; galling risk on the die |
| Copper, brass | Excellent drawability | Good for deep electrical and decorative draws; galling needs die attention |
Material and finish detail: materials and surface finishing.
The four failure modes and what causes them
- Wrinkling at the flange. Insufficient blank-holding force, or a blank that is too large for the first stage. Corrected by blank-holder pressure and blank size, not by a larger press.
- Tearing at the punch radius. Too much reduction in one stage. The fix is an extra stage, a larger punch radius, or a more drawable material temper.
- Wall thinning and a raised rim. Normal in drawing, but it must be anticipated. If the drawing calls a uniform wall thickness, it cannot be met — the wall thins as material flows from the flange.
- Earing. Anisotropy in rolled sheet produces a wavy rim. Usually trimmed in a later operation; if the rim is visible, plan for trimming.
Knowing which of these applies to your geometry is what a drawing review is for. It is also why we do not quote a deep drawn part from an outline alone.
Drawing plus secondary operations
Most drawn parts need more than the draw. Pierced holes, trimmed rims, flanged edges, embossed features and threaded inserts are usually added in the same tool or in a following station. Building them into the die from the start is cheaper than adding a second tool later.
Finishing applies after forming: zinc plating, powder coating, electrophoresis and deburring, selected by corrosion and appearance requirement. Electrophoresis is often the practical choice for drawn enclosures because it reaches inside the drawn section.
Specification summary
| Materials | SPCC, Q235, 304 stainless, copper, brass, aluminium |
|---|---|
| Thickness | 0.5–10 mm for stamping; deep drawing practical range 0.5–4 mm |
| Press range | 30–400 T |
| Stages | Single and multi-stage draws, confirmed per geometry |
| Secondary operations | Piercing, trimming, flanging, embossing in the same or following station |
| Finishing | Zinc plating, powder coating, electrophoresis, deburring |
| Sampling | 7 days after requirements are confirmed |
| Production | 15–25 days after sample approval |
| Inspection | Height gauges, fixtures, CMM; wall thickness checks |
Frequently asked questions
How deep can you draw in one stage?
It depends on material, thickness and diameter. Mild steel tolerates roughly half the blank diameter in the first stage; stainless considerably less. We confirm the stage count for your geometry during review.
Can the wall thickness stay the same as the blank?
No. Material flows from the flange into the wall, so the wall thins and the rim thickens slightly. If your drawing specifies uniform thickness, it needs revising — this is one of the most common drawing corrections we raise.
Do you anneal between stages?
For stainless and heavily reduced draws, yes — inter-stage annealing restores ductility. It adds a step and is priced accordingly, which is why the stage count matters to the quotation.
Can you draw a rectangular box?
Yes, within limits. Rectangular draws are less uniform than round ones: the corners need more stages than the sides, and the blank shape is not a simple circle. Send the geometry and we will confirm feasibility.
Can drawn parts be plated after forming?
Yes. Electrophoresis is often the better option for enclosures because it coats the inside of the drawn section. Zinc plating works for simpler geometries.
Request a quote
Send the drawing, material and temper, thickness, quantity and target date to robert@hmstamping.com, or use the quote request form. For drawn parts, include the internal depth and any wall-thickness requirement — those two figures decide the stage count.
Related: metal stamping · sheet metal bending · custom metal stamping parts · prototype process comparison
KEEP READING
