Custom Stamped Clips and Retainers
Custom stamped clips and retainers to your drawing — retaining clips, spring clips, grounding clips, cable clips and snap-fit features, formed from stainless steel, spring-tempered steel and copper alloys in 0.5–10 mm.
Clips are the one product family where the part has to work as a spring, not just as a shape. Outline and hole position are easy; spring rate and fatigue life are what decide whether the clip still holds after ten thousand cycles.
Clip types we produce
- Retaining clips and retaining rings
- Spring clips and snap-fit tabs
- Grounding and bonding clips
- Cable and hose retaining clips
- Panel and trim fastening clips
- Battery contact and terminal clips
Spring rate starts with material
A clip deflects and returns. How much force it takes to deflect it, and whether it returns fully, is set by three things: material, thickness and the geometry of the flexing section.
| Material | Behaviour as a clip | Practical note |
|---|---|---|
| 301 / 302 stainless, spring temper | Best spring properties | Not in our standard range — confirm at enquiry |
| 304 stainless, cold worked | Usable spring, moderate fatigue life | Work hardening from forming contributes to the spring; over-forming reduces it |
| Spring-tempered carbon steel (e.g. 65Mn) | High spring force | Needs to be confirmed as available; often heat treated after forming |
| Phosphor bronze, brass | Good conductivity plus spring | Common for contacts; lower force than steel at the same thickness |
| SPCC / Q235 | Formable but poor spring | Suitable for a locating clip, not for a loaded spring |
Be explicit about the material standard. “Stainless clip” covers 301 spring temper and 304 annealed, and those two behave nothing alike. If your drawing calls a spring grade outside our standard range, we will tell you at enquiry whether we can source it or whether the part belongs with a specialist spring stamper.
Fatigue: where clips actually fail
A clip that works once and fails after a thousand cycles almost always failed at a stress concentration. Three places to look:
- Sharp internal corners. Every sharp corner in the flexing region is a crack initiation site. A generous radius costs nothing on the drawing and can double fatigue life.
- Burr on the tension face. Burr on the side that goes into tension is a notch. Specify burr direction away from the tension face, and specify deburring where the clip flexes.
- Over-deflection in assembly. A clip designed for 2 mm of travel that is installed at 5 mm will yield on first fit. If installation travel is larger than working travel, that has to be designed in.
We raise these during drawing review because they are drawing changes, not process changes — much cheaper to fix before the die is cut.
Heat treatment and an honest limit
Spring properties in steel often come from heat treatment after forming. Heat treatment is not part of our in-house process. We form, deburr and finish; if your part requires stress relieving, hardening and tempering, that is an out-of-house step we will tell you about rather than absorb silently.
What we can do reliably: clips formed from cold-worked stainless where the forming itself provides the spring, and clips where the load is light and the cycle count is modest. Where the application is a high-cycle spring, be direct about it at enquiry — a clip that passes the sample and fails in service is worse than a declined order.
Specification summary
| Materials | 304 stainless, copper, brass, SPCC, Q235, aluminium; spring grades on request |
|---|---|
| Thickness | 0.5–10 mm, confirmed per drawing |
| Press range | 30–400 T |
| Processes | Blanking, piercing, forming, bending |
| Finish | Zinc plating, powder coating, electrophoresis, deburring |
| Not in-house | Heat treatment, hardening and tempering |
| Sampling | 7 days after requirements are confirmed |
| Production | 15–25 days after sample approval |
| Inspection | Height gauges, fixtures, CMM; functional deflection check on request |
Frequently asked questions
Can you make a clip with a specified spring rate?
We can form to a geometry and check deflection force on a sample. Specifying a spring rate in N/mm is possible if you can also accept the material and heat-treatment route it implies — tell us the target and the tolerance and we will say whether it is realistic.
Do you heat treat clips?
No. Heat treatment is out of house. We will tell you when a part needs it rather than quote as though the forming alone will deliver the spring.
Can you supply 301 stainless?
It is outside our standard material range. Ask at enquiry and we will confirm whether it can be sourced for your quantity.
How do you control burr on a clip?
Burr direction is set by die design, and deburring is available as a finishing step. Specify which face goes into tension and the maximum burr height — on a flexing part this is a fatigue requirement, not a cosmetic one.
Can clips be plated?
Yes: zinc plating, powder coating or electrophoresis. Note that plating on a thin spring section can affect fatigue life, and hydrogen embrittlement is a real risk on high-strength steel — raise the application and we will flag it.
Request a quote
Send the drawing, material standard, thickness, deflection requirement, cycle life if known, quantity and target date to robert@hmstamping.com, or use the quote request form.
Related: custom metal stamping parts · steel brackets · metal stamping · materials and surface finishing
KEEP READING
