Custom Metal Stamping Services

Harmonyos Metal Stamping produces custom stamped parts from customer drawings — brackets, clips, mounting plates, retainers, terminals and formed sheet metal components. We run 30–400T presses in Liaocheng, Shandong, China, and supply OEM and Tier-1 buyers in Malaysia, Vietnam and Thailand.

Every project starts with a drawing review, not a price list. We check geometry, material grade, thickness, hole pattern, bend sequence, burr side and datum scheme before quoting, so the sample you approve is the part we can repeat at volume.

What we stamp

Parts are made to your drawing. If you only have a sample or a sketch, send photos with critical dimensions marked and we will confirm what needs to be defined before tooling starts.

Capacity and process range

Item Range Notes
Press tonnage 30–400 T Press selected by part size, material strength and die design
Material thickness 0.5–10 mm Confirmed per drawing and application
Materials Q235, SPCC, 304 stainless, copper, aluminum Customer-specified grades accepted
Processes Blanking, piercing, bending, forming, deep drawing Single-stage, compound and progressive dies
Surface finishing Zinc plating, powder coating, electrophoresis, deburring Selected by corrosion and appearance requirement
Sampling 7 days Small-batch samples after drawing and requirements are confirmed
Production lead time 15–25 days After sample approval
Monthly capacity Approximately 100 tons Subject to product mix
Inspection Height gauges, inspection fixtures, CMM Inspection reports available on request
Quality system ISO 9001 Established 2011

How the press is selected

Tonnage is not chosen by habit. Three things decide it: the blank size and die footprint, the shear strength and thickness of the material, and how many operations run in one stroke. A 2 mm SPCC bracket with four holes and two bends behaves very differently from a 6 mm Q235 structural plate with the same outline.

We confirm the press during drawing review and tell you if the part needs a compound die, a progressive die, or a simple single-stage tool. That decision drives both the tooling cost and the per-piece price, so it is worth settling before you commit to a volume.

Materials

We stamp Q235 carbon steel, SPCC cold-rolled sheet, 304 stainless steel, copper and aluminum, plus customer-specified grades. Thickness runs from 0.5 mm to 10 mm, confirmed per drawing.

Material choice affects more than cost. Stainless work-hardens and needs different die clearance. Aluminum tears if the bend radius is too tight relative to thickness. Copper needs attention to galling. Tell us the application and the environment the part will see, and we will flag the forming risks before the die is cut.

Full details are on the materials and surface finishing page.

Surface finishing

Zinc plating for general corrosion protection, powder coating where the part is visible or exposed, electrophoresis for complex geometries and hidden surfaces, and deburring where handling safety or fit matters.

Finish specification should be on the drawing. If it is not, we will ask — plating thickness and coating type change the part dimensions at the tolerance limit, and that is much cheaper to resolve before production than after.

Quality control

Inspection uses height gauges, dedicated inspection fixtures and a CMM, with reports available on request. First-article inspection is performed on the sample and repeated at the start of each production run.

For parts with a critical fit, we agree the inspection points with you during drawing review — which dimensions are checked, at what frequency, and what happens when a reading sits at the limit. Documented control is more useful to your receiving inspection than a generic certificate.

More on our approach: quality control.

From drawing to repeat order

  1. Drawing and feasibility review. We check what is defined, what is missing, and where the part will be difficult to form. You get questions, not a silent quote.
  2. Material, tooling and process planning. Die type, press, finish and inspection plan are fixed together, because they constrain each other.
  3. Sample production and inspection. Small-batch samples within 7 days of confirmed requirements, with dimensional report.
  4. Approved revision and repeat production. The approved sample becomes the reference. Production runs in 15–25 days after approval.

What to send for a quote

Send the drawing, material and thickness, surface finish, required quantity or annual demand, critical tolerances, and target delivery date plus destination country. If any of these are open, say so — we would rather discuss them than quote against assumptions.

The RFQ checklist lists exactly what helps us quote accurately.

Frequently asked questions

What is the minimum order quantity?

MOQ depends on the part, the die and the material. A simple bracket cut from a standard coil has a very different economic floor from a progressive-die part with a dedicated tool. We confirm MOQ in the quotation rather than publishing a number that would not hold.

Can you work from a sample instead of a drawing?

Yes, if critical dimensions are identifiable. We will measure the sample and produce a drawing for your confirmation before tooling. Parts with tight fits usually need a proper drawing because wear on the original hides the true nominal.

How fast can I get a sample?

Small-batch samples in about 7 days after the drawing, material and requirements are confirmed. Time before that depends on how quickly open questions are closed.

Do you handle the tooling or do I own it?

We build the tooling and discuss ownership and maintenance terms as part of the quotation. Ask explicitly if you need the die transferred to another supplier later — it is easier to agree up front.

What tolerances can you hold?

It depends on material, thickness, feature type and die design. Rather than publish a single figure that would be wrong for most parts, we confirm achievable tolerance per drawing during review and state it on the quotation.

Which countries do you ship to?

We currently support customers in Malaysia, Vietnam and Thailand, and quote other destinations on request.

Request a quote

Send your drawing and requirements to robert@hmstamping.com or use the quote request form. Tell us the annual volume even if the first order is small — it changes which die we recommend.

Related: sheet metal bending · deep drawing · stamped products · materials and finishing

◌

LET’S TALK ABOUT YOUR PART

Request a quote

Share your drawing, material and quantity.

Request for quotation

    By submitting this form you agree to be contacted about your enquiry.

    Custom stamping parts made to drawingRequest a quoteWhatsApp
    Export support for customers in Malaysia, Vietnam and Thailand · See what to send for a quote