Custom Mounting Plates

Custom stamped mounting plates to your drawing — motor plates, sensor and actuator mounts, base plates, adapter plates and reinforcement panels. Made in SPCC, Q235, 304 stainless and aluminium from 0.5 mm to 10 mm on 30–400T presses.

A mounting plate is usually a flat part with holes in it, which is exactly why it is underestimated. The two things that decide whether it works — flatness and hole position relative to a datum — are the two things most often left off the drawing.

Applications

Flatness: the requirement nobody writes down

Stamping puts stress into sheet metal. Holes relieve it locally, forming adds to it, and the plate that was flat on the die comes off slightly dished. On a plate carrying a linear rail or a sealing face, that dish is a functional failure — the part rocks, the rail binds, or the gasket leaks.

What determines flatness after stamping:

Practical advice: put a flatness figure on the drawing, even a loose one. “Flat within 0.5 mm over the mounting face” is a specification we can hit and inspect. Silence means the default, and the default is whatever the process produces.

Hole position and datum

Hole-to-hole distance is usually less important than hole position relative to the face that locates the plate in the assembly. Two rules cover most problems:

  1. Dimension from one datum. Drawings dimensioned from three different edges produce arguments at inspection. Pick the locating face, dimension everything from it.
  2. Say which holes are the mounting holes. A plate with eleven holes usually has four that matter and seven that clear something. The four get the fixture and the tighter tolerance.

For plates that must mate with an existing part, send a sample or a scan of the mating surface. Reconstructing a hole pattern from a worn part is possible but the wear has to be accounted for.

Materials

Application Typical choice Note
General machine mounting Q235, 3.0–6.0 mm Weldable and stiff; heavier than needed for light loads
Precision interface plates SPCC, 1.5–3.0 mm Tight thickness control gives repeatable flatness and hole position
Lightweight panels Aluminium, 1.5–3.0 mm Lower stiffness for the same thickness; check deflection
Washdown or corrosive service 304 stainless Work hardens; different die clearance from carbon steel
Electrical isolation or weight Aluminium with powder coating Coating thickness affects hole fit — allow for it

Specification summary

Materials SPCC, Q235, 304 stainless, copper, aluminium
Thickness 0.5–10 mm, confirmed per drawing
Press range 30–400 T
Features Pierced holes, slots, embossed ribs, formed edges, countersinks (secondary)
Finish Zinc plating, powder coating, electrophoresis, deburring
Sampling 7 days after requirements are confirmed
Production 15–25 days after sample approval
Inspection Height gauges, fixtures, CMM including flatness

Frequently asked questions

How flat can you hold a stamped plate?

It depends on thickness, plan area and hole density, and it improves with a straightening operation. Give us the requirement and the geometry and we will confirm what is achievable rather than guess.

Can you match a hole pattern from an existing plate?

Yes. Send the plate or a drawing. If you send a worn sample, expect us to measure it and confirm the nominal with you before tooling.

Do you counterbore or countersink holes?

Countersinking and counterboring are secondary stamping operations. Tell us if they are needed — they change the process route and the price, and it is better to know at quotation.

Can the plate be tapped?

Tapping is a secondary operation. For thin plates, a pressed or extruded thread form is often stronger than a tapped hole in 1 mm material — worth discussing if the thread carries load.

What tolerance should I put on hole position?

Whatever the assembly actually needs, and not tighter. A general ±0.2 mm is common for clearance holes; mounting holes that locate a component may need less. State the figure rather than leaving it to a title-block default.

Request a quote

Send the drawing, material, thickness, finish, quantity and target date to robert@hmstamping.com, or use the quote request form. Include a flatness requirement if the plate mounts anything that must stay aligned.

Related: steel brackets · U brackets · custom metal stamping parts · metal stamping

◌

LET’S TALK ABOUT YOUR PART

Request a quote

Share your drawing, material and quantity.

Request for quotation

    By submitting this form you agree to be contacted about your enquiry.

    Custom stamping parts made to drawingRequest a quoteWhatsApp
    Export support for customers in Malaysia, Vietnam and Thailand · See what to send for a quote