Stamped Parts for Electrical and Electronics
Stamped electrical and electronic components — terminals, contacts, grounding tabs, shielding covers, chassis brackets and DIN-rail clips — produced to drawing in 0.5–10 mm copper, brass, aluminium, SPCC and 304 stainless on 30–400T presses.
Electrical stampings are judged on two things that drawings often leave implicit: contact resistance and burr. A terminal with the right outline and the wrong edge finish will still heat up in service.
Components we produce for electrical and electronic equipment
- Terminals, lugs and wire connection tabs
- Grounding tabs and bonding plates
- Contacts and contact springs
- Shielding covers and screening cans
- Chassis brackets, card guides and mounting plates
- DIN-rail clips and enclosure mounting hardware
- Busbar plates and connection links
Materials for conductive and structural parts
| Function | Typical material | Note |
|---|---|---|
| Current-carrying terminals | Copper, brass | Conductivity drives grade choice; confirm alloy on the drawing |
| Grounding and bonding | Copper, brass, zinc-plated steel | Plating choice affects contact resistance more than base metal |
| Shielding and covers | SPCC, 0.5–1.0 mm, zinc plated | Thin gauge forms easily; watch flatness on large covers |
| Chassis brackets | SPCC, 1.0–2.5 mm | Tight thickness control gives consistent bend angle |
| Outdoor or humid enclosures | 304 stainless, aluminium | Stainless work hardens; aluminium needs larger bend radius |
| Busbars | Copper, aluminium | Cross-section and hole position carry more tolerance risk than outline |
Burr, edge quality and contact resistance
On a structural bracket, burr is a handling concern. On a terminal or contact, it is an electrical one. A raised burr reduces effective contact area and can create a local hot spot under load; on a spring contact it changes the spring rate.
Practical consequences for the drawing:
- Nominate burr direction. Burr toward the non-contact face, or specify a maximum burr height. It is a specification, not a default.
- Specify deburring where it matters. Deburring is within our finishing range and is usually the cheapest way to control edge quality.
- State the contact surface. If one face carries current, say which. It determines both burr orientation and whether that face can be used for handling.
- Check plating against contact resistance. Plating is not cosmetic on a terminal — it is the contact interface.
Plating: what we do and what we do not
Our finishing range is zinc plating, powder coating, electrophoresis and deburring.
Electronic parts frequently call for tin, nickel or silver plating. We do not offer those in-house. If your drawing specifies tin-plated copper terminals or silver-plated contacts, tell us at enquiry: the stamping itself may well be within our capability, and we will say plainly whether we can supply the finished part or only the stamped and deburred component for plating elsewhere. Pretending otherwise wastes your time at sample stage.
Detail on the options we do offer: materials and surface finishing.
Thin gauge: where our range starts
Our press range handles material from 0.5 mm to 10 mm. Many electronic stampings are designed at 0.2–0.4 mm, which is below our range. If your part is in that band, we are not the right supplier and will tell you so at enquiry rather than quote and fail.
Parts from 0.5 mm upward — chassis brackets, shielding covers, busbars, heavier terminals — are within scope.
Specification summary
| Materials | Copper, brass, aluminium, SPCC, Q235, 304 stainless, customer-specified grades |
|---|---|
| Thickness | 0.5–10 mm, confirmed per drawing |
| Press range | 30–400 T |
| Processes | Blanking, piercing, bending, forming, deep drawing |
| Finish in-house | Zinc plating, powder coating, electrophoresis, deburring |
| Finish not offered | Tin, nickel, silver and gold plating |
| Sampling | 7 days after requirements are confirmed |
| Production | 15–25 days after sample approval |
| Inspection | Height gauges, fixtures, CMM; reports on request |
| Quality system | ISO 9001 |
Frequently asked questions
Can you stamp 0.3 mm brass terminals?
No. Our range starts at 0.5 mm. For thin-gauge terminal work we would refer you elsewhere rather than take an order we cannot run reliably.
Do you supply tin-plated parts?
We stamp and deburr the part; tin, nickel and silver plating are outside our in-house range. We can supply the component for plating at a facility you nominate, and we will say clearly which route we are quoting.
How do you control burr on contact surfaces?
Burr direction is set by die design, and deburring is available as a finishing step. Specify the contact face and the maximum burr height on the drawing — it is much easier to agree than to inspect after the fact.
Can you produce shielding cans with drawn sections?
Yes, within the thickness range. Deep drawing is one of our processes; send the geometry and we will confirm the draw ratio and whether one stage is enough.
What about flatness on large covers?
State the requirement. Large thin covers distort from forming stress and hole density, and straightening adds a step. Agreeing a flatness figure at quotation avoids a rejected batch later.
Request a quote
Send the drawing, material and temper, thickness, plating specification, quantity and target date to robert@hmstamping.com, or use the quote request form. If the plating is outside our range, say so in the first email and we will tell you what we can supply.
Related: deep drawing · custom metal stamping parts · materials and surface finishing · industries we serve
KEEP READING
