Stamped Parts for Machinery
Stamped brackets, mounting plates, guards and reinforcement parts for industrial machinery, automation equipment, agricultural and construction machinery — produced to drawing in 0.5–10 mm steel, on 30–400T presses, with zinc plating, powder coating or electrophoresis as required.
Machinery parts usually carry load and locate something. Two consequences follow: thickness is chosen by force rather than by habit, and flatness often matters more than the edge tolerance anyone remembered to put on the drawing.
Parts we produce for machinery builders
- Motor, gearbox and bearing mounting plates
- Frame brackets, gussets and corner supports
- Guard plates, covers and access panels
- Rail and linear-guide mounting plates
- Linkage plates and lever components
- Reinforcement plates for welded frames
Automation and packaging equipment tends to need many small brackets in modest quantities — a shape that suits compound dies and short production runs rather than one large progressive tool.
Load, thickness and flatness
Three things decide whether a machinery bracket behaves:
- Load direction. A bracket loaded in the plane of the plate behaves very differently from one loaded across a bend. Tell us the direction, not just the part number — a 3 mm bracket that is adequate for a 20 kg static load is not adequate for the same load with vibration.
- Thickness and bend radius together. In Q235 above roughly 6 mm, springback and minimum bend radius both grow quickly. A radius that forms cleanly at 3 mm will crack at 8 mm, and the fix is either a larger radius or a different material — both of which are drawing changes.
- Flatness after stamping. Hole density and forming stress both pull a plate out of plane. If a mounting plate carries a linear rail, state the flatness requirement. Straightening is possible, but agreeing a number at quotation is cheaper than a rocking plate at assembly.
Materials and finishes
| Application | Typical choice | Note |
|---|---|---|
| General frame brackets | Q235, 3.0–6.0 mm | Weldable, predictable forming, lowest material cost |
| Precision mounting plates | SPCC, 1.5–3.0 mm | Tighter thickness control, cleaner surface, consistent bend angle |
| Guards and covers | SPCC, 0.8–1.5 mm, powder coated | Thin gauge forms easily; coating hides handling marks |
| Washdown or humid plant | 304 stainless | Work hardening changes behaviour at the second bend |
| Inside formed sections | Electrophoresis | Reaches surfaces spray coating cannot |
More detail: materials and surface finishing.
Interchangeability across a machine build
Machinery is assembled, not just used. A bracket that fits machine one and needs filing on machine forty is a production problem, not a quality complaint — and it usually traces back to a dimension that was never nominated as critical.
Two things prevent it:
- Nominate the assembly-critical dimensions. Usually hole position relative to a datum face, and the distance between mounting faces. Everything else can carry a general tolerance.
- Dimension from one datum. Drawings dimensioned from three different edges are hard to inspect and easy to dispute. Pick the face that locates the part in the machine.
We agree the inspection points during drawing review, so the fixture checks the dimensions that affect assembly rather than the ones that are easiest to measure.
Specification summary
| Materials | Q235, SPCC, 304 stainless, copper, aluminium, customer-specified grades |
|---|---|
| Thickness | 0.5–10 mm, confirmed per drawing |
| Press range | 30–400 T |
| Processes | Blanking, piercing, bending, forming, deep drawing |
| Finish | Zinc plating, powder coating, electrophoresis, deburring |
| Sampling | 7 days after requirements are confirmed |
| Production | 15–25 days after sample approval |
| Monthly capacity | Approximately 100 tons, subject to product mix |
| Inspection | Height gauges, fixtures, CMM; reports on request |
| Quality system | ISO 9001 |
Frequently asked questions
Can you produce brackets for a machine that is still being designed?
Yes, and prototype quantities are a normal starting point. Send the concept drawing; we will flag what needs to be defined before a die is worth cutting, and where a press-brake prototype would be cheaper than tooling.
Do you weld assemblies?
Brackets are stamped and formed. Where a gusset or second component is needed, we discuss the assembly route with you rather than assume welding is included in the price.
How do you handle a part that must be flat?
State the flatness requirement on the drawing. It depends on material, thickness, hole density and whether the part is straightened after forming. It is much easier to agree a number than to argue about a rocking plate at receiving inspection.
What is the minimum order quantity?
It depends on the part, the die and the material. A simple guard plate and a progressive-die mounting bracket have very different economic floors, so MOQ is confirmed per part in the quotation.
Can you match parts currently bought elsewhere?
Yes. Send the drawing or a sample. If you send a physical sample, expect us to measure it and produce a drawing for confirmation first — a worn part does not define the nominal.
Request a quote
Send the drawing, material, thickness, finish, quantity and target date to robert@hmstamping.com, or use the quote request form. If the part carries load, tell us the load direction and whether vibration is involved.
Related: steel brackets · mounting plates · custom metal stamping parts · industries we serve
KEEP READING
